These jacks are designed to lift and support laboratory equipment like baths, stirrers, heaters, flasks etc. Re‐fitting a diffusion pump using a jack becomes a simple task. The height is easily adjusted with a large knob.
|Cat. No.||Platform (mm)||Min. Height (mm)||Max. Height (mm)||Max. Static load (kg)||Construction material|
|T310‐AL||100 x 100mm||Anodised aluminium|
|T310‐SS||100 x 100mm||Stainless steel|
|T315‐AL||150 x 150mm||60mm||200mm||50kg||Anodised aluminium|
|T315‐SS||150 x 150mm||200mm||60kg||Stainless steel|
|T320‐AL||200 x 200mm||70mm||290mm||50kg||Anodised aluminium|
|T320‐SS||200 x 200mm||90mm||290mm||60kg||Stainless steel|
|T710||Diecast alloy clamp for 1 burette, securely held in place by 4 rubber-covered knobs. Simply bring levers together, insert burette, release levers. Holds tubes up to 28mm diameter. The bosshead fits rods up to 19mm.|
|T711||Economy style double burette clamp holds two burettes in self-closing jaws.|
|T712||Accommodates a burette at both ends. Holds gently without blocking markings on burettes|
Moulded in polypropylene burette clamps. The spring loaded jack in the middle provides a vice like grip on the burette and prevents it from slipping. Two tapered wedges ensure firm grip on rods of 9 - 13mm diameter.
T715 The round jaws will gently hold a burette and lock at any angle. Single jaw opens approximately 10mm to 45mm rotatable 360 degrees. Overall length approximately 165mm.
T716 is made from chrome‐plated zinc‐alloy. Either side can be adjusted to fit articles from 0 to 60mm in diameter.
T717 is made of chrome‐plated alloy. The PVC coated prongs will hold very small articles up to 50mm in diameter.
T717‐B is made of chrome‐plated zinc‐alloy. The PVC coated prongs fit articles from 0 to 25mm in diameter.
T718 is made of Ni/Cr plated die‐cast alloy, with four cork‐lined prongs, max. opening 75mm, holds max. tube diameter 85mm. Total length 250mm.
T718‐B is made chrome‐plated zinc‐alloy. The cork‐lined interlocking jaws fit articles from 0 to 80mm in diameter and is rotatable 360 degrees locking into position.
If used in an adverse environment they can rust. After use in an acidic environment rinse clamps and dry before storage.
T720 and T722: Fixed right angle bosshead, diecast alloy, metal screw, plastic screw heads.
T723 Holds rods up to 19mm in diameter. One-piece aluminium clamp holder with fixed jaw angle.
For joining an upright and two horizontal bars at right angles. Requires a 2.5mm Allen key.
Closed retort support rings with bosshead to attach to support stand rod. Made of Ni/Cr plated steel.
Heavy stainless steel sheet with rubber protected edges, 2 holes.
The rod is 700mm long (680mm above the base) and is 9.7mm in diameter.
Larger rods may be custom made in an engineering machine shop.
Please note: There is remaining stock from a previous manufacturer where the rod is 750mm long. We will continue to supply these rods until stock is depleted. If this is not suitable for you, please contact us before your order is placed.
Non-corrosive, stable retort stands. The base is made of polystyrene coated gypsum plaster, the rod is polypropylene coated steel. The rod screws firmly into the base.
|Cat. No.||Base length (mm)||Base width (mm)||Base height (mm)||Rod length (mm)||Rod diameter (mm)|
An open jaw, nickel plated brass clamp for flexible rubber tubing. Regulates the flow from open to close. Lower jaw has a swivel-mount for easy insertion of tubing without disconnecting apparatus.
Due to its special shape, this connector can be used for a wide variety of different tubing inner diameters.
Non-return valves with nitrile rubber (NBR) valve discs. Max. operating pressure 2 bar.
With valve disc made from fluorocarbon rubber (FKM). Max. operating pressure 2 bar.
Crystal clear. The flow monitor provides a visual indication of the flow rate of liquids or gases through tubing. The impeller functions in both flow directions. For liquid flow rates from 150 mL/min.
Dimensions: length 88mm, width 40mm, height 15mm.